Sunday, March 17, 2024

How To Get Mold Off Shower Tiles

How To Get Rid Of Grout Mould

Cleaning Tile : How to Remove Mold From Shower Tile

Fortunately, there are several methods for removing the mould between your tiles. A number of different chemical and natural cleaning agents can be used to get rid of mould, but its important to remember that when using these products, you should always work in a well-ventilated area, ideally with an open window. Its also vital that you wear rubber gloves to protect your skin and goggles to safeguard your eyes from any potential splashback.

How To Clean A Shower Curtain

How do you remove mould from the shower curtain though? While they can be incredibly cute , they can also be massive mould traps that need some serious cleaning and maintenance to prevent them from getting ruined and smelling.

However, the process of removing mould is not necessarily a hard one, and we have two excellent methods for getting the job done. The first of these is by using a baking soda and vinegar solution to remove the mould in question, the steps for which are below:

#1 Remove the shower curtain from the shower.

#2 Place it in the washing machine with a couple of bath towels .

#3 Add half a cup of baking soda alongside your usual washing tablets and start the cycle.

#4 Once it reaches the rinse stage, stop the machine and add half a cup of white wine vinegar and then allow the cycle to finish.

#5 Remove the curtain from the machine and hang it out to dry. The mould should be gone. If not, you can repeat the process a couple of times.

You may find that the baking soda and vinegar method isnt quite enough though, and in cases like this, you can try our next method. This one uses bleach, which means it is a lot more powerful and so likely to be effective on curtains that are severely mouldy. Here are the steps for you:

#1 Place the curtain in your washing machine with some bath towels, for the same reason as the first method.

#4 Once it has finished washing, hang it out to dry, and the mould should be gone.

Further Reading: Old Shower DIY Makeover

How To Remove Mold With Baking Soda

Unlike bleach, baking soda wont harm or discolor the tiles or present any health hazards to the occupants of the home. It will clean the affected area very well, but wont be as efficient in killing the mold spores as bleach.

There are several different ways you can use baking soda to clean the tiles and grout in your home:

  • Mix 1/2 cup baking soda with one gallon of water and spray the mixture on the affected area. Wait for about half an hour, then rinse the surfaces thoroughly with warm water
  • Dip a damp sponge into pure baking soda and scrub down the tiles and grout with it. Rinse with warm water
  • Stir 1/2 cup of baking soda and several teaspoons of water to make a paste you can spread directly over the mold. Apply the paste to the moldy grout, let it sit for 10 minutes, then scrub away with a bristle brush. Rinse with water and repeat, if necessary.

Good to know: You can use borax to clean mold in the same way as baking soda it is highly alkaline and very effective at cleaning, disinfecting, and deodorizing.

Recommended Reading: Mold Off Leather

Natural Remedies For Dealing With Mold In The Shower

For decades, homeowners used bleach for cleaning the bathroom and disinfecting surfaces.

Using bleach may remove mold stains from non-porous materials such as porcelain tubs, showers, and toilets but does not help remove mold on grout or wood.

Bleach is also ineffective for killing mold, bacteria, and fungus. It neutralizes some harmful particles and helps remove stains but does not truly kill the mold.

Luckily, there are alternative solutions. You can make powerful cleaning agents that work on almost any surface, including:

  • Tubs and shower surrounds
  • Metal fixtures
  • Walls and ceilings

While the cleaning solution that you mix should work on everything, the way that you apply the mixture depends on the type of surface. You can wipe non-porous surfaces clean but may need a brush for scrubbing mold from grout and wood.

First, you need to create a cleaning mixture. These options require ingredients that you already likely have in the bathroom or kitchen, including vinegar, hydrogen peroxide, tea tree oil, and baking soda.

These are just a few of the home remedies for getting rid of mold but they are among the most effective.

How To Get Mold Out Of Grout Lines

How to Get Rid of Mold &  Mildew In a Shower

Most often, people question how to clean mold from grout without bleach? The question is somehow valid since bleach can ruin the surface due to its harsh contents. This is why you must have experienced discoloration on any surface after using bleach. Well, thankfully, there are alternatives to bleach when trying to get rid of bathroom tile mold. Refer to the steps mentioned below to know how to execute the method.

Method 1:

  • Protect yourselves with safety gear which includes masks, goggles, and rubber gloves.
  • Scrub off as much mold as possible using a sponge, rag or a brush. We suggest you go for a brush since its more effective.
  • Fill an empty spray bottle with distilled white vinegar and let it sit for a while.
  • Once the surface is dry, start scrubbing off the mold again. Make sure you do it thoroughly for better results. Also, dont go overboard with scrubbing as this will damage the grout itself.
  • Spray the vinegar onto the grout again and let it settle for at least thirty minutes.
  • Carefully rinse the area with warm water and properly dry out the surface to avoid mold regrowth.
  • Repeat the steps if you still feel the presence of mold.
  • Method 2:

  • Wear safety gear and scrub off the maximum mold
  • Create a paste by mixing half a cup of baking soda and multiple teaspoons of water.
  • Spread the paste on the grout and allow it to settle for half an hour at least.
  • Scrub the mold again and rinse the surface with warm water.
  • Keep repeating until the mold is out of sight.
  • Read Also: Remove Mold From Leather Couch

    Distilled White Vinegar And Water For Colored Grout

    Vinegar is somewhat acidic, and so it will kill the mold growth. It should also not harm any colored grout.

    White Vinegar and Water Recipe to Remove Mold

    • 1 cup of white vinegar
    • 1 cup of warm water
    • Spray bottle

    Mix equal parts warm water and white vinegar in a spray bottle. Spray the solution liberally on the grout and shower tiles and give it 20 minutes to soak into the grout mold. Scrub away at the grout mold with an old toothbrush or other brush.

    This is an excellent method to remove mildew from grout without expensive cleaning agents and just a bit of elbow grease and time. Find additional hints for cleaning black mold out of the grout with vinegar for mold in the shower and other areas of the home.

    How To Clean Mould Off Bathroom Sealant

    For sealant, similar to grout, you may need to replace it entirely. If the mould is on or around your tiles, you should be able to scrub or brush it away with your cleaning solution, potentially bleach-based or borax for its strength.

    Like removing grout, use a flat-headed screwdriver to lift it away and apply new sealant. Remember to clean the tiles, grout and sealant regularly.

    When using bleach, remember that it is a toxic substance that can cause eye, lung and skin irritation. Take great care and make sure you have enough ventilation to remove fumes.

    A handy trick is to roll a few pieces of toilet paper into a sausage shape, pour the bleach onto the affected sealant and let it soak in. Place the toilet paper on top, allowing it to absorb the bleach. Leave it for 12 hours and then remove it. You may need to repeat it. Watch the video below for an example.

    Don’t Miss: Rash From Mold

    How To Avoid Stains On Ceramic Tiles In The Kitchen

    The following three steps will help you to avoid stains on ceramic tiles within the kitchen:

  • Mop your ceramic tiled floor at least once a week with very hot water.
  • Wipe up any food or drink spillages as quickly as possible to avoid them settling, and ideally, wipe the surface with an antimicrobial cloth afterwards.
  • If you have stains and molds that wont wipe away, try mixing half a cup of vinegar with a gallon of water and continue to mop the floor as usual. Rinse the floor with warm water after youve cleaned the stain and remove all of the liquid from the tiles . Youll get the same results using this method for ceramic wall tiles and ceramic kitchen countertops.
  • Baking Soda Plus Hydrogen Peroxide

    Cleaning Mold: How to Remove Mold From Shower Wall Grout

    Apply a thick baking soda paste to the area affected by mold. Spray or carefully pour hydrogen peroxide over the baking soda paste so it begins to fizz, which will help loosen the mold further. Scrub the fizzing paste using a stiff bristle brush, then rinse the paste and mold away with water. Repeat as needed.

    Tip: If thereâs mold on the caulk that seals around your tub, faucet, sink or toilet, the safest thing to do is remove the caulking. Sterilize the area with bleach or distilled white vinegar and dry it thoroughly before replacing the caulk. Opt for a mildew-resistant caulk to inhibit the growth of future mold. Some mold problems canât be tackled with home remedies or commercial cleaners found at your local store. If youâre facing stubborn grout mold or too much mold to handle alone, call the pros at ServiceMaster Clean for complete mold removal from any area.

    Read Also: How To Remove Black Mold From Shower Tile

    Recommended Reading: How To Clean Moldy Shower Grout

    Best Products For Cleaning Mold On Shower & Bathroom Grout

    There are countless ways to clean the grout in your shower and bathroom. The method you use will depend largely on personal preference as well as the severity of the mold growing on your grout. In some cases, you may not need anything other than an old toothbrush and soap. There are, however, several other products that you can use to clean your grout.

    Most of these methods work best when applied with an old toothbrush or a small cleaning tool with stiff bristles. This will allow you to truly scrub the mold from the surface of the grout.

    Remove Mold And Mildew From Bathtub Corner Tiles With This Simple Hack

    Make your shower shine like new.

    When youre cleaning your bathroom, nothing is more frustrating than trying to remove stubborn mold and mildew. The worst site for stuck-on mold is the shower corner tiles and the corners of your bathtub. But luckily, removing the grime from bathroom corners is easier than ever thanks to a super simple cleaning hack youll wish you knew about sooner.

    You May Like: What Causes Mold On Ceilings

    Your Complete Guide To Getting Rid Of Bathroom Mold

    Mold is an ugly four-letter word that is found all too often in bathrooms. Learn the best ways to remove bathroom mold and prevent it from coming back.

    With warm, humid conditions, the bathroom is the perfect place for mold, and it can grow on just about every surface. Once you find it, cleaning mold in the bathroom can be a big chore. Follow our tips for cleaning moldincluding products to use, instructions for specific surfaces, and key prevention tacticsto refresh your bathroom. You’ll want to make sure you get it all so you arent constantly fighting mold in the bathroom.

    Editor’s Tip: If you suspect your bathroom has black mold, known as Stachybotrys chartarum, seek a professional to test it, as you may have a larger problem at hand. If the results indicate other common household molds, move forward with our cleaning tips.

    Is Shower Mold Toxic

    How to get rid of bathroom mold and mildew quickly ...

    Due to the way bathrooms and showers are constructed today, the black mold you see in your shower is less likely to be the really hazardous type of mold. This is because your shower areas and surfaces dont have cellulose which is required for most of the really hazardous types of mold to grow.

    That isnot to say that one of the more toxic molds cant ever grow in your shower. Theycan. If you have a bigger issue in your bathroom or home and THOSE spores haveinfiltrated your shower then your shower can become a breeding ground for somereally bad mold. But regular ol mold in the shower usually more allergenicthan anything.

    You May Like: How To Get Rid Of Mold On Bathroom Ceiling

    How To Clean Mold From Bathroom Tiles

    Scrubbing with vinegar or a borax solution is a great way to clean mold from bathroom tile. For small applications, mix 2 tablespoons borax into 2 cups warm water and funnel into a spray bottle. Spray the solution on tiles and let it sit for a few minutes. As noted earlier, you can also make a large-batch tile cleaning solution with 1 cup borax and 1 gallon of warm water. Use a mop or sponge to scrub away the mold. Whether you use vinegar or borax, there is no need to rinse the solution. However, you will want to dry the floor so the moisture doesnt encourage the mold to return.

    To clean mold from bathroom tile grout, use the same borax or vinegar solution as before. Apply it directly to grout lines and let it sit. Use a toothbrush or another small bristle brush to clean mold from bathroom tile grout. For hard-to-remove stains, mix two parts baking soda with one part vinegar to form a paste. Apply it to the grout and let it sit a few minutes before scrubbing away mold. If desired, you can also use a commercial grout cleaner.

    Editor’s Tip: Check your tile material before using one of these solutions. Vinegar can be damaging to some tile materials avoid if you have marble, slate, granite, or stone tiles.

    How To Remove Mold From Grout

    Removing mould from grout is a tough job and has potential health hazards. Because mold reproduces through spores, extra caution must be taken to prevent breathing in spores in the air. Personal protective gear should be worn when handling and cleaning mold. There are many types of mold that grow in homes, some with worse reputations and hazards than others. One of the most dreaded forms, black mold, can cause serious health conditions. Black mold removal may be completed by you as long as the area isnt too large and protection is worn.

    You May Like: How To Get Mold Spots Off Bathroom Ceiling

    Learn How To Clean Mold In Shower Grout Naturally With Borax

    Borax is a step up from vinegar or peroxide. If you need to know how to clean your shower head or clothes, look no further than Borax. It cuts through grease and dirt with ease, and it makes a superior bathroom-mold cleaning solution, too.

    • 1 cup Borax

    Mix the water and Borax in the spray bottle. Spray any mold, and let it sit. You dont have to rinse Borax off, so it keeps working for a long time. Use the solution as an after-shower spray to prevent mold growth.

    What Is Black Mould And Why Does It Form

    HOW TO CLEAN A MOLDY SHOWER (super satisfying clean with me!)

    Mould is a fungus that grows in damp, warm conditions, such as a bathroom, where there is very little airflow. It can start as mildew, a white form of fungus found on a flat surface.

    The growth of black mould on bathroom walls and ceilings is due to excess moisture, which may start with condensation building up over time following a shower or bath. The warm, moist air meets a cold surface and clings to it, like windows.

    Mould can build-up for many reasons, apart from a lack of ventilation in your bathroom these include leaking pipes, poor insulation or if condensation has not been removed following a shower.

    Also Check: How To Clean Mould From Ceiling

    How To Prevent Mold In Grout

    The drier the tiles, the smaller the chance of mold developing in the grout lines.

    As you certainly know, prevention is the best cure. And indeed, why spend so much time and effort cleaning mold from grout, when you can simply prevent it from appearing altogether? All you need to do in order to keep mold under control is to deprive it of the main prerequisite for its growth moisture. Just keep the tiles dry and youll never have to worry about the harmful microorganisms.

    But how can you remove moisture from a room that is designed to be wet such as the bathroom, for example? It sounds absurd.

    You cant, of course, but you can reduce the dampness there is a big difference between getting wet and staying permanently wet.

    Here are some simple, yet highly efficient measures you can take to lower the humidity in your bathroom, kitchen, and other wet areas of your home and prevent mold growth:

    1. Keep doors and windows open for as long as possible to ensure proper air flow within the home:

    • Let the bathroom window stay open for at least 15 minutes after you turn the shower off, so that excess moisture can move out of the room rather than condense on the walls and tiles
    • Leave the shower door open when the shower is not in use
    • Keep the kitchen windows open while cooking to allow the steam to escape
    • Ventilate the laundry room, basement, and attic as often as possible.

    8. Fix leaky faucets and showerheads to remove the source of excess moisture in your bathroom and kitchen

    Popular Articles
    Related news