Can Bathroom Mold Cause Illness
For the most part, mold just looks bad. For some, it can irritate allergies and asthma.
Mold is relatively harmless, but given the right circumstances it can definitely cause some irritation, Tolliver said. If you have pre-existing allergies or COPD or some sort of respiratory condition, the spores can actually irritate the lining of your lungs and can increase your risk of asthma attacks or COPD exacerbation.
People who are affected by bathroom mold will most likely experience runny noses, coughing and scratchy throats.
Ogden noted that people with allergies should be tested for which specific allergens bother them so they can best protect themselves. Mold is one of the irritants that can be identified through allergy tests.
Doctors can and should identify what the culprit is, she said.
Over-the-counter treatments can frequently ease the feeling associated with an allergy attack, but more severe cases could require a doctors intervention.
Minor adjustments can keep mildew and mold in check to prevent potential allergies.
Cleansers with bleach, or even white vinegar, can often keep the slimy, hairy growths from taking root in the bathroom. Wearing gloves and a mask can protect people from inhaling any mold spores as they scour the bathroom surfaces.
These are some expert-approved steps to stop mold from colonizing the bathroom in the first place:
Follow TODAY Health and Wellness on and “One Small Thing” for easy tips to improve your life every weekday.
Why Is There Mold Around The Air Conditioning Vents
Friday, September 21, 2018
The louvered metal grille that directs conditioned air from a duct into the room is called a register, and mold around an air conditioning register can have several causes:
1) If the cold air coming out of the register is too cold compared to the room air, condensate will form on the surface of the register and migrate over to the surrounding drywall. Wet drywall will begin to grow mold within a few days. The register in a bathroom is more likely to have mold growth because the high humidity in the room provides more moisture for condensation.
;; The difference between the room air and cold air coming out of the register is called the temperature differential or split, and more than about a 22º F split can cause condensate to form.;
2) Duct air leakage above the register or at the connection of the duct to the register can also cause condensate to form, even if the temperature split is not excessive, because the air in the unconditioned attic or wall cavity may be significantly warmer. If squirrels or rodents get into the attic, they may ;shred openings in ducts for material to make their nests. Workmen in the attic also occasionally cause duct damage that leads to leakage.
;; Home inspectors like us that have an infrared camera are able to detect duct connection leakage before it causes ceiling problems. The cold areas show up as blue in the bottom photo below of a leaking register connection to duct.
What Are The Black Spots On My Bathroom Ceiling Are They Mold
Have you ever carefully sighted dark spots on your bathroom ceiling? While taking a close look, you must find these little guys disrupting your shower rooms interior. Dont you acknowledge that as a matter of fact, the creatures are sort of black mold? The alive microscopic organisms own inky appearance coating the horizontal surface out of the blue.
Not only does the black mold occupy the ceiling but also it easily adapts to the porous surroundings such as drywall, rug, fabrics as well as the wooden furniture. The wet-bulb temperature creates high humidity and not to mention the shadowy condition plainly support the ideas of murky fungus growth. It might develop rapidly due to sufficient food source.
In comparison to other molds, the black mold requires slower development. Once the wet surroundings, as well as the great nutrient, support the life of fungus, the growth remains going on faster. The mold colonization usually needs 1 to 2 days.
Recommended Reading: How To Clean Mold Off Plastic Cutting Board
How To Clean Black Spots In The Bathroom
Find out how to clean black spots in the bathroom with a few supplies and a little elbow grease.
Have you ever been taking a relaxing bath, only to look up and notice black mold growing on the ceiling? Yuck. Its a problem no one wants to deal with, but unfortunately is a common occurrence in bathroomsespecially if your home is located in a moist climate. The good news is, you dont have to live with that mold forever. Find out how to clean black spots in the bathroom with a few supplies and a little elbow grease.
Where To Look For Bathroom Mold
The main problem with bathroom mold is that it can appear almost anywhere from caulk to towels. Bathroom is perfect for mold growth due to a constant high level of humidity.
If you want to check your bathroom for signs of mold, then you should pay attention to these places:
- Caulk, grout, and tiles
- Towels and bathroom robes
- Shower curtains and mats
Of course, if you are not sure whether or not you have mold in your bathroom , you can always rely on professionals to do all the necessary checks. Furthermore, they will provide insights into how to keep your bathroom mold-free. In case you already have bathroom mold, they will deal with it effectively to prevent it from coming back.
Also Check: Does Black Mold Cause Seizures
Dangers Of Black Mold And Mildew
People who are exposed to mold spores can have different symptoms, such as a stuffy nose, sneezing, wheezing, and itchy skin or eyes. Some could even have an intense reaction such as fever or difficulty breathing, especially if they have allergies to molds. Some people can develop asthma. People who have respiratory problems or weak immune systems can be at risk of mold infections.
According to the CDC, the molds themselves are not toxic or poisonous. Moreover, the hazards that are carried out by molds may produce mycotoxins that could be dangerous to people. There are reports, rare but possible, that these toxigenic molds can cause serious illnesses such as pulmonary hemorrhage or memory loss.
If you see any signs of bathroom mold, it is best to call in professionals. Other surfaces of your bathroom might also be affected, such as tile grout and ceiling drywall. Removing and replacing the affected area can be the best long-term solution.
Tip 9 Cover Up The Mess
Bathroom ceilings are often painted in light colors, so probably white, beige, neutrals, or pastels. So even after youve removed the mold, your bathroom ceiling may still be stained. Double-check to ensure all the mold is gone before you remove the visible evidence. Youll have to sand off the stains, apply chemical treatments, or paint over those unsightly marks.
Painting is the most common option, especially because bathroom ceilings are rarely made of wood. This is why you have to double-check that all the mold is gone. Otherwise, the mold spores will be trapped beneath the paint and may continue to grow, eventually poking through.
Recommended Reading: What Kills Mold Spores On Wood
Hellowe Had Insulation Blown Into Our Attic We Are Concerned If There Was Mold Before The Insulation Was Installed How Do We Check That
Its very unlikely mold would grow beneath the insulation.; Condensation is the most common cause of mold growth in an attic.; Condensation occurs on the underside of the roof sheathing, not beneath the insulation.; Mold growth beneath the insulation would require a roof leak, which youd typically notice on the ceiling inside the home before any real mold growth occurred.
A Tree Fell On My House Recently And When We Had Builder Go In The Attic To Do Repairs They Discovered Mold We Had The Whole Roof Replaced And Were Getting A Ventilation Fan Installed When The Mold People Came Out After The House Roof Was Replaced They Said The Mold Had Gotten Worse Some Say Its Because We Have A Lot Of Fish Tanks In The Basement And Heat Lamps For Pets On The Second Floor Others Say Its Cause The Roof Is Leaking Some Say Its Because Of A Leaky Pipe How Do I Find The Cause Is There A Company That Will Determine The Cause I Need To Find Out
Fish tanks can be a major contributor to mold growth.; They add a large amount of moisture to the indoor environment.; Due to the stack effect, this moisture migrates upward through a home, and eventually into the attic.; The heat lamps are not a problem.; If you plan on keeping the fish tanks, ensure you have continuous exhaust ventilation on the top floor of the home.; This can be accomplished with a constant flow fan such as the Panasonic WhisperGreen.
These issues are often due to a combination of factors.; In your case, the roof might be under ventilated as well.; Often a single vent fan is not sufficient.; I recommend verifying that the entire roof is well ventilated.; Check out our page on attic ventilation.
Recommended Reading: How To Clean Mold Around Air Vents
The Landlord Of The Building Says The Brown Particles On The Bathroom Ceiling Are Dust How Can You Tell If It’s Mold
A simple tape lift mold test can determine if its mold.; Here is an example.; ;Mold growth on a bathroom ceiling is nearly always due to inadequate ventilation.; If you have a working bath fan, I recommend installing a programmable timer switch.; This will toggle the fan on and off throughout the day.; If no fan is currently present, install a Panasonic WhisperGreen fan.; These run continuously on a low speed mode and ramp up to full speed when the bathroom is occupied.
How To Remove Mold From Drywall
Removing mold from drywall can be tricky because if drywall gets too wet, it is ruined. In fact, its often easier to cut out the infected section of drywall and replace it, rather than trying to treat the mold directly. If the drywall feels soft, its beyond saving. However if you do want to clean the drywall without removing it, heres what to do.
Step 1: Brush the mold off the drywall using the scrubbing brush. Try to remove as much as possible without getting the wall wet.
Step 2: Make a 50/50 solution of white vinegar and hydrogen peroxide. Spray it onto the area until it is damp, but not soaked.
Step 3: Wait 10 minutes then use a medium-bristled brush to clean the wall using circular motions. Dont scrub too hard or youll damage the drywall.
Step 4: Wipe down the wall using household disinfectant wipes.
Step 5: Allow the wall to dry. In high-humidity environments, set up a box fan directed toward the wall to dry it as quickly as possible.
If the drywall is stained when dry, use a primer or stain block before repainting. Consider a mold-resistant paint to provide extra protection, and reduce humidity in the room to stop mold from returning.
Pro Tip: Learn How To Remove Humidity from Your Furniture and Textiles for Proper Moisture Control
Read Also: How To Install Vinyl Stair Nose Molding
Hi I’ve Been Having Problems With One Of My Upstairs Bedrooms There Has Been Multiple Yellow Drips Above The Window A Week Later They Turn To Mould Clean It Off With Mould Spray And The Same Thing Happens Again Insulation Has Been Fitted In The Past Few Months But It Is Still Occurring
Was it occurring before the insulation was installed? There are a couple of potential causes. Often the insulation is pulled back from the soffits to allow for proper air flow. This creates a cold spot in the last 6 or so inches where the ceiling meets the exterior walls. If a home has elevated humidity , condensation and mold growth can occur. Running the bathroom exhaust fan throughout the day can greatly reduce the relative humidity in the home. Also, ensure the insulation contractor placed insulation as close the edge as possible . A scan with a thermal imaging camera will readily show whether this is occurring. Youll see an obvious blue spot in the exact location of the moisture and mold growth.
The other possibility is a roof leak or gutter issue. If you live in a snowy, cold climate, ice damning can also cause an issue like this.
Clean And Remove From Popcorn Ceiling
Cleaning a popcorn ceiling can be especially challenging and take great skills. You need to get rid of the fungal growth without loosening this material and causing it to fall on the floor.
To get rid of it, you can try using a soft sponge that you soak or dip in diluted bleach. It may not be advisable to use ammonia if you want to avoid the possibility of staining the ceiling.
You also may need to spend more time washing this type of material. You cannot use the same vigor to scrub and wash it as you would other materials. Still, with time and close attention, you can rid the popcorn of fungus.
Also Check: How To Clean Mold Between Pavers
Tips For Mold On Your Bathroom Ceiling
Mold can be a pretty scary thing. It looks horrible on a white ceiling so its easy to panic when you spot it. In reality, mold spores are everywhere. Its a type of fungus, so if your ceiling is moist, these floating spores will attach and start to grow.
Ceiling mold is mostly black, but it can also be white, green, gray, or even purple. And its a common problem for bathrooms because theres so much moisture. So while you cant avoid getting your bathroom wet, lets look at some tips to deal with mold on your bathroom ceiling.
Tackling The Underlying Cause Of Mold
Molds are all around us we breathe in their spores every day. Its impossible to prevent mold from entering any property, but steps can be taken to stop mold from finding a new home in your house. Without addressing the underlying cause of why mold is growing in a particular area, it will just keep coming back.
Molds only need two things, food and damp. Its impossible to remove the food mold needs from your home, because your property is made of it. Particle board, gypsum, wooden framing, and soft furnishings can all nourish and sustain large mold colonies. What you can control, however, is damp. When mold is discovered, look for the underlying source of water.
There are three common ways that water can cause problem mold growths:
- Maintenance issues such as leaking pipes or failed window seals
- Human error, for example not drying water in shower door tracks or splashing water around a sink
- Construction-related, usually relating to ongoing condensation issues caused by poor airflow
The first two are easy to resolve. Simply repair the problem or change your habits to be more conscious of where water is splashing and pooling. If mold is growing because of the construction of your property, it may require more extensive intervention. Installing fans or vents, replacing portable heaters, or investing in a dehumidifier might be necessary to resolve the problem.
Also Check: Will An Ozone Machine Kill Mold
Hi Since March 30 We’ve Noticed Some Weird Staining Occurring On The Walls And Ceiling Throughout Our Apartment They All Start Out As Clear Then Some Changes Colors I Reached Out To Our Property Management On March 30 And Again On May 7 Because Now My Entire House Is Sick And Showing Symptoms Associated With Mold Exposure My Landlord Had Yet To Come Out To Determine If It Is Mold I’m Growing Frustrated For Obvious Reasons And I Have Been Searching The Web For Insight Into What This Staining Might Be I Can’t Get Anyone To Come Out Because That Process Needs To Be Initiated By Our Landlord Which Has Been Unresponsive To This Point My Question Isbased On Pictures Could This Be Either Ghosting Condensation Or Mold
This type of staining is typically due to heavy condensation.; You see it most often in a bathroom. It can also occur in rooms with high humidity and poor ventilation.; The condensation is leaching; out chemicals/contaminants from the paint.; Ghosting causes perfectly straight lines which correlate to the underlying framing.; Examples of ghosting.
How To Remove Mold From Inside Walls
The inside of your walls is a great environment for mold, but a terrible one for you to find and clean. Often homeowners dont realize there is mold inside their walls until its causing a major problem. Warning signs include an earthy, musty odor in the home, allergy symptoms that clear up when you leave the property, and stains or dampness on the wall itself. If mold does get inside your walls, youll probably need a pro to handle it. At the very least, the drywall has to come down in order to properly access and treat the mold and prevent it from coming back. You can mitigate the damage by looking out for the warning signs, and reducing the humidity in your property.
Read Also: Can Black Mold Be Removed From Wood
Taking Care Of The Grout
Cracked grout is the perfect surface for mold to grow on, and its often the place where you can spot it easily. Replacing your shower grout every 6 months is the most important step you can take to keep mold out of your bathroom. Its best to clean your tiles and grout once a week with a pH-neutral cleaner, to prevent mold from invading and developing.
Each time you change the grout, make sure to seal it with a latex penetrating sealer. The pores in the grout will absorb it, which will provide protection from mold. While it is true that some of these sealers can be expensive, a choice of high-quality sealer will keep your grout mold-free longer than the 6 months we mention above.