Where To Put Crown Molding

Our Best Tips And Tricks For An Easy Install

• use flat crown. Let me repeat that: USE FLAT CROWN!

• hold crown down about 1/2 to mask uneven ceilings

• start install in the most-visible corner and work around the room from there. That way, if you end up with some wonky angles and less-than-perfect cuts, they wont be super obvious.

• Use paintable caulk to fill holes, seams, and small gaps in corners

• Painting the wall and crown the same color and with the same paint means you dont have to tape and itll hide any ups and downs in the crown

• we didnt have one, but if you have access to a laser level it would be helpful to check where your ceiling is high and where its low before you start this project. Once you know those elevations, you can start your crown in the middle of the two . That way you wont end up too close or too far from the ceiling.

Okay, thats everything weve learned about crown molding since we first did a horrible job installing it a decade ago . Wed love to hear from you! Leave a comment with any questions, tips, or anything that will make us smile, laugh, or cringe. And if you use this tutorial, wed love to see it! Tag us on .

Can You Cut Crown Molding With A Circular Saw

A circular saw is another very common tool that can be found within the tool line up of many handymen and women. The circular saw is a tool that could be considered primarily universal when it comes to its capabilities, but it is designed to make straight cuts. If you are putting up crown molding and are looking to use a circular saw to make the cuts, is this tool capable of delivering what is needed to ensure the proper cut of your material?

You can use a circular saw to cut crown molding, but keep in mind that it is only able to make straight cuts. For those cuts that need to be at an angle, attach a speed square to end of the piece you are cutting to angle the cut with accuracy without having to find another tool.

How To Install Crown Molding: Cut The Molding

Swivel the saw to a 45-degree angle to match the direction of the molding, set the board against the saw at the mark and make the cut.

For scarf joints, do not turn the boards upside down. They will lay flat on the saw. The swiveling part of the saw table stays centered during this cut. Instead, tilt the saw blade to a 45-degree angle and make the cut. The boards should then fit perfectly together.

Read Also: Wet Molding Leather Holsters

How To Install Crown Moulding With A Nail Gun

Installing crown molding uplifts the aesthetics of your interior by giving your wall and ceiling a distinctive decorative look. Depending on the size and designs of your moulding you can definitely bring your own artistic touch in your own home. It can be used to cover any kind of defect on your walls too.

You may think that it will be a hassle to install the crown moulding by yourself and you will need professional help for it. But you can easily install crown moulding with a Nail gun by following a few simple and easy steps. Using a nail to install crown moulding can save time and keeps the moulding damage free which can occur due to the use of a hammer.

Now follow the five easy steps to install Crown molding with the help of a nail gun.

How Much Does It Cost To Install Crown Molding

Crown molding ranges from $6 to $25 per foot, depending on the material you choose. Wood and plaster tend to be cheaper, while metal tends to be the most expensive option. If you are planning on installing the crown molding yourself, you will only have to worry about this cost and the cost of any materials needed to install the crown molding.

You will need to purchase or buy tools such as a saw, a stud finder, and a tape measure. You will also need consumables such as nails and sandpaper. While this can be pricy, especially if you have to purchase the larger tools, it will still be cheaper than hiring a professional.

If you choose to have your crown molding professionally installed, you will still have to purchase the materials, but you won’t have to worry about buying the tools. You will need to pay labor, though, which could cost between $1,000 and $1,200 depending on the number of rooms that need crown molding installed.

Read Also: Uv Lights To Remove Mold

Nailing Crown Molding To A Profile Backing

As you probably know, most crown molding sits at an angle from your wall to your ceiling. This means that to nail it off, there are relatively narrow points where the molding hits a solid surface. To avoid dealing with this, you can cut a piece of plywood or scrap board to fit into the triangular space behind the molding.

In this case, you nail the profile backing to the studs, rafters, and top plate. Then when you are ready to put the molding in, you can nail it wherever you want into the piece of scrap. This allows you to focus more on the finished look rather than making sure you are nailing through the right place on the molding and into framing behind the wall.

Recommended Reading: Dashing Diva Nail Guard

What Is The Difference Between Molding & Crown Molding

Molding is an imprecise term used for any trim layout inside of a space. In general, this would fall under crown molding as a sub-category, while crown molding can be used for anything and everything that has been pulverized from a wooden element.

With time, as the interior designs became more impactful, both types evolved too, becoming more ornate. But recently simplicity is returning as an aesthetic desire.

Also Check: Clean Bathroom Mold From Ceiling

Uses Of Crown Molding

Crown molding was once exclusively used to close the gap between the wall and the ceiling. Now it is becoming useful material to decorate our homes and different types of furniture. It reflects the persons personality and raises the worth of a home.

We see crown moldings are being used to bring a sophisticated feel to a furnished space, add style and narrow the gap in a room with a high ceiling. Not only does it function to transform the beauty of old houses, but it also works to transform the grace of modern homes into a classy, elegant, and vintage look according to your personality.

Lets look at some specific areas where crown molding can be used.

Lets have a look at them in the following section

Pro Tips For Installing Crown Molding

Crown molding is not easy to install, but the right trim can transform a room. Here are illustrated step-by-step guidelines that prove that a skillful layout and smart shortcuts can change any apprentice carpenter into a ceiling molding master.

The first time I installed crown molding,I probably wasn’t really installing it at allI was just handing my dad tools off the truck. Since then, I’ve put it in eight or 10 rooms, and around half a dozen bookcases and cabinets. Crown can go in any space, from the kitchen to the den, and of all the interior trim found in a home, none attracts more attention. A room with crown perched high at the wall and ceiling junction has an eye-catching focal point that a savvy realtor will point out along with granite counters and marble baths.

This job’s 4½-inch crown came from a local lumberyard–still the best place for a wide-profile selection. I splurged on clear pine at $2.70 a linear foot. If I intended to paint the crown, I could have gotten preprimed finger-jointed pine for $1.60–and I’d be able to caulk over stray gaps before painting.

Installing crown is a bit trickier than other trim because it requires cutting compound angles. Plus, out-of-square corners and bulging, wavy walls can be a nightmare for a novice. But over the course of a dozen jobs, I’ve come up with a few shortcuts–I don’t really remember where I learned a lot of these tricks, I just know them.

Recommended Reading: Get Rid Of Mold On Bathroom Ceiling

Cut Outside Corner Miters

• Miter outside corners with the molding upside down.
• Cut the piece about 1/16-inch beyond the length mark and then shave off a bit if the piece is too long.

• Check the length at outside corners using a test scrap.
• When the length is right on, set the piece aside.
• Then cope, miter and test-fit the other outside corner piece.

Do Crown Moldings Increase The Value Of A Home

If you are looking for a quick-fix solution that makes your home value shoot way up, without a real investment on your part, crown moldings are not your answer. However, if you are ready to make a reasonable investment to get quality moldings installed well, then yes, they will increase the value of your home.

Like most things in your home, quality matters when you are talking about crown moldings. If you purchase the cheapest moldings from the nearest big-box home improvement store, you are not going to impress a knowledgeable realtor or home-buyer. Likewise, if the moldings are installed in a hackneyed, less-than-professional manner, they will not add any value.

The key to increasing your home value with crown moldings is to get elegant, high-quality moldings, and to make sure they are installed in a professional way. That way, you will be able to enjoy the classy addition to your rooms, and you will see an improvement in the marketability of your home when you go to sell it.

– More living room ideas

Read Also: Ozone Machine To Kill Mold

Types Of Crown Molding

Crown molding only refers to the molding installed where the top of a wall meets the ceiling. Each style has its own use, although molds can be mixed to create the style you desire.

• Crown generally unites the wall and the ceiling. Its so called because it is the builders crowning achievement.
• Cove a molding with a concave shape which can go nearly anywhereat the ceiling/wall corner or the floor/wall corner. Its still crown molding, but a plainer version.
• Dentil a crown molding style with small, identically shaped squares or rectangles evenly spaced along the molding. Dentils are mostly found in historic homes.
• Batten a flat trim piece designed to hide the join between two pieces of paneling or wall. Other flat pieces are often installed, along with the serviceable batten, to create a design element out of a functional piece.
• Egg and Dart crown molding that has a pattern of what looks like eggs separated by darts.
• Bead and Pearl rows of symmetrical shapes that look like beads or pearls on the crown molding.

What Kind Of Crown Molding Should I Install

Like the previous question, the exact type of crown molding you should choose comes down to taste. However, here are some common concepts and situations to consider when planning out the design:

• Rooms with high ceilings look great with a wider, heavier crown.
• In rooms with elaborate details, the crown molding should be comparatively ornate.
• In terms of visual space, your crown molding and baseboard should be fairly similar.
• For small rooms or rooms with low ceilings, crown molding that has a lower profile will still look classy without being overwhelming. This will also prevent the crown molding from making the room look even smaller.

You May Like: How To Clean Mold Off Bathroom Ceiling Naturally

How To Install Crown Molding: Outside Corner Cut

For an outside corner cut, the bottom edge is short and the top edge will be long. On the right side of an outside corner, the cut will angle up to the left. On the left side, the cut will angle up and to the right.

A scarf joint is used to hide where two pieces of molding meet on a long wall. On both the right and left side of a straight joint, the cut will angle in the same direction.

Jalynn Baker

Jalynn Baker

Start With The Long Wall And Work In One Direction

• Install the longest piece of base trim to the ceiling first.
• Note: A long piece of trim or molding is clumsy to handle and hard to measure and cut accurately. Installing it first makes it easier because the first piece has square cuts at both endsno coping.

Also Check: Black Mold In Shower Ceiling

How To Install Crown Molding: Inside Corner Cut

For an inside corner cut, the bottom edge will be long and the top edge will be short. On the left side of an inside corner, the cut will angle up to the left. On the right side of an inside corner, the cut will angle up to the right.

For an outside corner cut, the bottom edge is short and the top edge will be long. On the right side of an outside corner, the cut will angle up to the left. On the left side, the cut will angle up and to the right.

Jalynn Baker

Jalynn Baker

What Nails Do You Use For Crown Molding

NailcrownusingnailsYouyounailingyouusingnailnailcrownusingnails

. Accordingly, can you use brad nails for crown molding?

Both are commonly used for installing baseboard, chair rail, door and window casing, crown molding, and door frames. One advantage to 15-gauge nails is that they are collated at an angle, which allows the nose of the nailer to reach into tighter spaces. Brad nailers use smaller 18-gauge nails up to 2 inches long.

#Ads

Likewise, how long should nails be for crown molding? Crown is typically nailed up with a 2 finishing nail and a compressor and finishing gun. Outside corners are usually done with a brad nailer and 1 brad nails with glue. Studs are generally 3-1/2, drywall a ½ and the crown moulding a minimum of ½ therefore 2 finishing nails are necessary.

Subsequently, question is, do you glue or nail crown molding?

That makes the crown molding easier to hold and the cut mark easier to see. Use construction adhesive on all raileven where you can nail into studs and ceiling joists. That way, you can use just enough nails to hold the trim in place until the adhesive sets, and youll have fewer nail holes to fill.

What angle do you cut crown molding?

Using a power miter saw is the best way to cut crown moulding angles. The saw can be adjusted to cut at any angleset it to 45 degrees for one side of a standard 90-degree corner. The saw can be set to 45 degrees to the left or 45 degrees to the right.

Also Check: How To Get Rid Of Mold On The Bathroom Ceiling

Crown Molding Alternatives Save Money

Bringing elegance and maintenance to your house does necessarily have to be an expensive endeavor. You can gain the same aesthetics and satisfaction using cost-friendly alternatives.

A budget homeowner is a smart homeowner. You know how incredibly unprecedented owning a your own home is when you first get started.

Crown molding alternatives are a fantastic integration to your house, in terms of satisfaction and looks. And they let you save up enough for buying other décor items. Isn’t that a pure win-win situation?

Vinyl Or Pvc Crown Molding

The average price of vinyl or PVC crown molding ranges from $1 to $3 per linear foot. Vinyl is known for being strong, durable, and a reliable choice for molding. Its easy to cut and installs without breaking or chipping. Vinyl can be used both indoors and outdoors, and its a good option if you want to put crown molding in a bathroom or kitchen because it doesnt absorb moisture. Its also great for hiding cables and rope lighting.

Cons

• Its brittle so it can crack during installation because of having to drill nail holes in it to install it.
• Its not flexible.
• It doesnt take paint well.
• It doesnt come in many style options or colors.

Also Check: How To Remove Mold From Ceiling In Bathroom