Do Mold Bomb Foggers Really Work

Ulv Cold Fogging Vs Thermal Fogging

ULV cold fogging or misting is the most frequently selected DIY mold fogging method. This is because it is cost effective, easy to do, and doesnt require you to stay out of your home for any period of time. However, there is a time and place for thermal fogging or even a combination of both. Lets take a quick look at these two mold fogging methods.

How To Use A Bomb Fogger

Using a mold fogger is simple and just requires a little planning and patience.

• Clear out any items that could be damaged by the mist and moisture.

Mold fogging solutions are safe for clothes and contents, but always take precautions with extra precious items.

Better safe than sorry. Remove items such as electronics, papers, instruments, other important objects before misting.

• Fill your fogger with the fogging solution. You may want to do this outside. Some are messy to fill!
• You are using a mist, so a lower mist setting will be less likely to damage your home or your things. A stronger stream could definitely damage items that are sensitive to moisture. Experiment with the spray settings outside if possible before starting your job.
• A stationary fogger just needs to be set up with the head positioned to best cover the room. Turn it on for the desired time and let it go! Dont set the timer for too long. When done, turn it off and let it sit while the fog settles.
• For a handheld mold fogger, just start spraying into each air vent. Put It on the finest mist setting for contents and spray until everything is covered with a light mist. Be sure to spray ceilings, walls, window sills, and floors.
• After fogging, open windows, turn on fans, and let the area dry.

Damage Buddy Tips

If you want to check the effectiveness of the fogger you can test the air in the area a few days after you do the treatment. Simple test kits are found at most hardware stores.

Follow directions!!

Is Mold Fogging Effective

Mold foggers arent an all-in-one mold solution. You need to make sure of the following first if you want them to be more effective:

• Find where the leak is. If theres visible mold, theres definitely a water or moisture leak somewhere.
• Dry out areas that are wet. Mold problems in constantly wet areas are common, so drying out wet area before the treatment can dramatically reduce the chance of recurrence.
• Remove the affected material. Whether its a part of a wall, a whole cabinet, ceiling tiles, carpet, or anything else, remove it so it doesnt cause mold regrowth.

You might be wondering why youd need to do all this. Again, mold fogging isnt an all-in-one solution, and thats because of this very simple reason: They may not be able to clear away active molds.

All were trying to say is that mold foggers are very effective in preventing mold regrowth and they can be an essential part of mold remediation, but they may not be able to get rid of mold if its already there. Dead spores may also still cause allergic reactions, and mold fogging doesnt get rid of these as well.

Anyway, after all of this is done, use the mold fogger for crawl space, large areas, or any affected part of the home. Foggers used for mold remediation can either be stationary, which are used to cover entire rooms, or handheld for smaller spaces.

Where Can We Use Mold Foggers?

• Basements, cellars, and attics
• Crawl spaces and roof spaces
• Garages and sheds

Recommended Reading: How To Clean Mold Between Pavers

How Do You Use A Mold Fogger

A mold fogger is a great product for getting rid of black mold but you should be aware its not the only tool youll need and fogging isnt the only thing youll have to do to get rid of your mold problem.

The EPA recommends fixing leaks that may be providing moisture for mold, scrubbing off hard surfaces with detergent or bleach and drying them completely before fogging. If the surface is too porous, you may have to remove it.

Some items in your house such as carpets, painting, and works of art may require the services of a special remediation company to come in and clean them.

Read Also:What are the best respirators for mold?

Once all of the preparation work is done, then you can use the fogger.

Fill the tank with the clean solution of your choice and follow the directions to set the nozzle and droplet size.

Smaller droplets should be used in areas with many cracks and crevices. In large open areas, you can use larger droplets.

Static foggers can set in the middle of the area to be fogged and switched on. Leave the area and close it off while the fogger is running.

When the fogging is completed, but before the cleaning solution tank runs dry, return to the area and turn off the fogger.

Open all the windows and doors, as well as any other openings that are available, and let the area clear. It may take half-an-hour to an hour for the air to clear and the mist to dry.

When And How To Use A Fogger

To use a total release fogger, you place the canister in an appropriate location, activate it, and leave the room .

Total release foggers are approved for use against a variety of indoor pests, including bed bugs. Not all foggers are labeled for use against bed bugs, so you need to read the label before purchasing a fogger to ensure you are getting one that lists bed bugs on the label.

You May Like: How To Clean Mold Between Pavers

Mold Remediation Available Nationwide

• Mold Removal Service in ChicagoWater Mold Fire Restoration of Chicago3521 N. Wilton AveChicago, IL 60657312-574-3814
• Mold Removal Service in MinneapolisWater Mold Fire Restoration of Minneapolis2800 North 2nd StreetMinneapolis, MN 55411651-395-7036
• NYC Mold RemediationWater Mold Fire Restoration of New York City1450 2nd Ave New York, NY 10021212-257-2169
• Mold Restoration in Fort LauderdaleWater Mold Fire Restoration of Fort Lauderdale1000 SE 2nd St.Fort Lauderdale, FL 33301 800-0801

• Washington DC Mold RemediationWater Mold Fire Restoration of Washington DC2200 Pennsylvania Ave NW Washington, DC 20037 650-0299
• Mold Removal Company in BostonWater Mold Fire Restoration of Boston5A Cornelia Court Boston, MA, 02120 701-7868
• Mold Removal Company in MiamiWater Mold Fire Restoration of Miami100 Biscayne Blvd Suite 1114Miami, FL 33132305-999-5144
• Atlanta Mold ServiceWater Mold Fire Restoration of Atlanta350 Ferst DrAtlanta, GA 30322 373-4654

• Philadelphia Mold ServiceWater Mold Fire Restoration of Philadelphia228 Race StPhiladelphia, PA 19106 645-2960
• Jersey City Mold ServiceWater Mold Fire Restoration of Jersey City100 Paterson Plank Rd Jersey City, NJ 07307 528-3997

Mold Removal Fogger: Benefits Usage Best Machine & Products

Whatever the case, the good news is, there are many approaches you can employ to remove mold from your home, and one of such approaches is the use of mold bomb foggers.

Do mold foggers work?

Keep reading this article, as we will be discussing all you need to know about mold bomb foggers and how they can work for you during mold removal.

Don’t Miss: Bathroom Ceiling Mold

How We Chose The Best Mold Killers

When narrowing down the list of the best mold killers, we looked for products that were effective and affordable. If youre going to be dealing with the mold issue yourself, youre going to want to choose a household spray that is simple, straightforward, and strogn. Working with potent, professional-grade mold killers can be extremely dangerous if you do not have the proper expertise. Many mold killers contain some toxic chemicals that can affect your health, so you should stick to a product thats made for everyday use. If you have to bring out the big guns, talk to a professional who works at a mold and water damage remediation company.

Our top pick, RMR-86, combines affordability with efficiency, making it the best mold killer for most people. This stuff works like magic, killing mold in seconds, right before your eyes. It kills all of the mold and leaves the area bright and clean, requiring no hard scrubbing on your part. All you have to do is spray. RMR-86 is simple and powerful, making that $20 price tag totally worth it. You want to be able to remove mold fast without having to work too hard, and thats exactly what this product gives you. Just always remember to wear the proper protective gear to avoid any health issues.

How To Use A Mold Bomb Fogger Safely And Correctly

1: First, check the can to see how many square meters the mold bomb can fog. If the room has more square meters than the fogger can handle, then you may want to consider using two cans.

2: Place the can in the center of the room and clear any obstructions. Close all windows and remove or cover/remove any sensitive items . Also, no humans or pets are to be in the room during fogging even if the fogging solution is non-toxic.

3: Set the fogger off as per instructions on the can. It will give you a couple of seconds to leave the room before the fog gets released. Leave the room and close the door for 2 hours while it sanitizes and disinfects.

4: Once sufficient time has passed, enter the room, open the windows and discard the can.

You May Like: How To Clean Mold Off Plastic Cutting Board

How Does A Mold Fogger Work

mold foggermoldmoldmoldare

Mold Control Fogger. Applying Concrobium Mold Control with a cold Fogger is an effective way to eliminate mold and musty smells in large or inaccessible spaces. A fogger evenly mists Concrobium Mold Control to saturate the air in the enclosed environment, and evenly coat all surfaces.

Similarly, does mold fogging really work? Fogging is an effective treatment offered by mold remediation specialists and often manageable with a do-it-yourself kit, but its effects are limited. Most mold fogging solutions kill mold spores, stopping them from spreading and reducing or eliminating musty odors.

Additionally, how do you fumigate for mold?

CLICK, SPRAY & WALK AWAY Place Mold Bomb in the center of the room, or if there is visible mold growth, place the fogger near the site of contamination. Simply remove the cap from the mold fogger and push the tab on the top of the can until it clicks and locks to begin fogging.

Is there a fogger for mold?

The fogger atomizes Concrobium Mold Control into a fine mist that quickly and evenly coats surfaces to eliminate existing mold and prevent mold growth. Fogging can be an ideal approach to mold remediation in damp, musty basements, attics, crawlspaces and any large area where mold is a concern.

How Do You Treat Mold Infestation In A House

Scrub the surface mold stains from walls and wood trim with a mixture of one quart water and 1/2-cup bleach mold cleaner to kill the mold. Use a soft brush and work until signs of the mold disappear. After scrubbing the surfaces, allow the bleach solution to continue to penetrate the surfaces and dry.

Read Also: How To Clean Mold From Leather

What Exactly Are They And How Do Flea Bombs Work

A flea fogger is a small aerosol canister that contains insecticide. To use this flea product, simple release one of them in each regular sized room to kill the fleas. The five chemicals that are usually responsible for controlling the flea outbreak are Cypermethrin, Methroprene, Nylar, Permethrin and Tetramethrin. Depending on brand, your flea fogger could contain one or more of those active ingredients and since they can be potentially dangerous for pets and even yourself, please make sure you leave the house while bombing.

Its important to note that foggers for fleas wont usually achieve a 100% removal rate for fleas in your home. However, I have found them very effective on empty houses that have carpeted floors . Since there is no furniture and other obstacles, the fogger mist usually reaches all areas in the house and the insecticide has some time to sit undisturbed on the floor, making sure that any survivors are eliminated. Since flea eggs are tiny and usually fall into the fibers in the carpet, this is actually an important step for these foggers to work properly.

So do flea bombs work? Yes, they are fairly effective for killing fleas but due to the toxins they release, I recommend only using them when the flea situation is very bad. There are also a few other problems like:

What Is A Mold Fogger And How Does It Work

A mold fogger is a device that is used to turn mold remedial solutions from liquid to fog. While you can easily put mold-killing solutions into a spray bottle and spray the affected areas, it is said for foggers to be more effective.

This is because the mold fogger turns the liquid solution into vapors, which can evenly distribute the solution. This means that it can reach cracks and gaps a spray bottle cannot reach. The fogger uses heat to vaporize the liquid solution that fills the room with a thick fog. Or by what is known as cold fogging which simply uses air pressure to vaporize the solution.

Read Also: Moss Prevention On Pavers

Remedy Air Treatment Dispenser

The battery operated Remedy air treatment dispenser slowly emits a safe, odorless concentrate of citrus and vegetable extracts over 8 to 10 weeks. This continuously and safely bio-balances your environment to reduce the levels of airborne mold spores and mycotoxins.

One dispenser & refill is perfect for a standard 12 x 12 room, but typically covers up to 400 sq ft. The dispenser can be hung on the wall or set on a flat surface.

What I love about the Remedy air treatment dispenser is that there is no burning candle to worry about. Seeing that I am involved in cat rescue, candles arent always ideal. This would hold true for a household with small children.

Much like the EC3 Candle, the Remedy Air Maintenance candle is a specially formulated soy-based candle to help maintain low mold environment. They emit a safe, odorless concentrate of citrus and vegetable extract that reduce the airborn mold and mycotoxin counts.

The Remedy candles lasts up to 30 hours. Burn 3 hours in each room to be treated the first day and 1 hour every 1 to 2 days thereafter.

You can purchase the Remedy Air Maintenance Candle here.

Another Reminder!

Fogging DOES NOT replace the professional, physical removal of visible mold colonization of walls, floors, ceilings, or under carpets. Fixing the water source and removing mold infestation safely and properly is critical.

Types Of Mold Foggers

There are two main types of mold foggers. It can either be a thermal fogger, which uses heat to turn your solution into vapor. Or it can be a cold fogger. These dont use heat in order to achieve the same effect.

All the foggers on this list are the ULV type, which are all cold foggers. These tend to be lighter and dont use as much power. The fog they produce isnt as visible as what you might get from a thermal one. This might seem like an advantage, but these fogs are comprised of chemicals so youre best avoiding them.

At the same time, some foggers are electrostatic. This means that they apply a charge to the particles in order to attract them to surfaces. This helps avoid wasting your chemicals as the fog wont simply drop to the ground. Most of it will drift towards any nearby surface.

You May Like: Mold On Cutting Board

Tips When Choosing The Right Fogger

Mold foggers are not made equal. Because they are manufactured by different companies and came in different models, some are better than others. Here are some tips to choose the right mold fogger for your needs:

• Choose a true fogger that generates particles of 50 microns and finer not a mister that produces only bigger particles.
• Consider the size of the area handheld foggers might be ideal for small corners, while a static model is better if you need to treat a larger area.
• Make sure to read the directions carefully when choosing fogging solutions.
• When you choose a mold fogging solution, read the directions carefully. Some products are not actually approved for the purpose needed. Some can be harmful to your health.
• Read the fine prints. Some products only cover the mold but dont immediately kill it.
• See if the product works on the surface you want to treat like drywall, wood, fabric, or concrete.
• Its best to choose a product that dries easily.
• Be careful in using water-based botanical products. Mold spores are hydrophobic and repel water. This means that fungicides in a water-based product may not kill mold spores.

The Ultimate Mold Foggers Guide

If you have ever had a mold outbreak in your house then you probably know that the mold you can see is only the beginning of the problem. Believe it or not, only 10% of mold is visible the other 90% is microscopic. On top of this, there is usually even more mold behind the scenes in the roof space, wall spaces, heating and cooling ducts and many other places that are inaccessible.

This is where a mold fogger such as the Concrobium fogger can make your life so much easier and have the mold problem under control in record time.

Disclosure: As an Amazon Associate I earn from qualifying purchases. However, this does not impact our reviews and comparisons. All opinions are our own we pride ourselves on keeping our articles fair and balanced. For more info see our disclosure statement.

Read Also: How To Get Rid Of Airborne Mold In House