How To Cut Crown Molding:
2. Begin by making your right-side cut for the inside corner molding: With your miter saw off, move the blade to the left at 45-degree angle. Turn on the saw and cut.
3. To make your left-side cut for the inside corner molding, move your blade to the right at a 45-degree angle, turn on the blade, and cut.
3. To make your right-side cut for outside corner molding, move your blade to the right and cut in a downward motion.
9. For the left-side cut for outside corner molding, move your blade to the left and again make a steady downward motion.
10. Match the seams of the boards up to make sure they align flush.
Now, you’re ready to install!
Follow House Beautiful on .
Setting Up Your Miter Saw To Cut Templates For 38 Spring Angles
This method of cutting crown molding can be done with any miter saw.
*These two things are constant:
*These two things willchange depending on the cut you are making.
How Do You Cut Crown Molding Corners
You cut and inside and outside crown molding corners at the exact same time when you hold the molding in the miter saw the correct way. It’s magic I tell you!
When you cut the trim that frames windows and doors, you typically put the back of the molding flat on the table of the saw.
In this case, the flat bottom of the saw is representing the wall of your home. You swing the saw to 45 degrees and make the cut.
When you do this on another piece of trim cutting the opposite 45-degree angle, the two pieces of trim will meet nicely at the upper corner of a window or door.
If you’re installing baseboard that’s not tall, you place the back of the trim against the vertical saw fence. This vertical face now represents the actual wall the baseboard will be nailed to. You make your 45-degree cuts and all is well.
Note when the casing and baseboard are against the wall, there’s no massive void space behind them. That’s why they’re so easy to cut in the saw.
Read Also: Why Do My Ac Vents Have Mold
How To Cut Crown Molding Inside Corners
This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. wikiHow’s Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards.There are 10 references cited in this article, which can be found at the bottom of the page. This article has been viewed 197,358 times.Learn more…
There are two ways to cut crown molding for an inside corner. The first method is to cut 2 pieces at an angle and fit them together. This is usually done with a miter saw. This method works best for perfect 90-degree corners where you dont need to worry about compensating for strange angles. The other option is to cope your corners. This is done by installing one piece of crown molding on top of an uncut piece that sits flush with the wall. To do this, youll need to miter one length, then use a coping saw and a file to wear away the wood behind the cut. Coping your corners will result in a tighter fit, but its harder to do and requires more work.
How To Cut The Outside Corners Of Crown Molding
This article was co-authored by our trained team of editors and researchers who validated it for accuracy and comprehensiveness. wikiHow’s Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards. This article has been viewed 7,281 times.Learn more…
Crown molding is a type of decorative trim used to cover the seam between a wall and the ceiling. Cutting it may seem like a daunting task, but it’s actually pretty simple. Start by finding the angle of the outside corner using a pair of 1 by 4 in boards. Then, cut the crown molding to the correct angle using a miter saw. With this DIY trick, youll ensure that the pieces line up perfectly. Note that this strategy is for crown molding that sits flush against the wall, not at an angle between the wall and ceiling.
Read Also: How To Get Mold Off Shower Grout
How To Measure Corners Using A Bevel Gauge And Protractor
The Easiest Way To Cut Foam Crown Molding
The easiest way to cut molding is by using a DIY crown molding kit that has clip-on corner pieces. In our kits, we provide , creating a more straightforward installation process overall.
You’ll find that the entire installation process with our patented snap-on crown molding system is a breeze, especially when it’s time to cut your crown molding pieces. With traditional crown molding, you have to miter the edges of your material. Our kits have connector blocks and corner pieces so you don’t need to miter anything in rooms with corners of 90 degrees. The cuts for joints also don’t have to be perfectly straight since our Moulding Mates will cover the imperfections.
The process gets even simpler when you see what you need. You may already have the tools you need to complete one of our Focal Point crown molding projects. If you don’t, rest assured that they are useful tools that are easy to acquire, including:
- A flat work surface
- A handsaw, power saw or utility knife
- A straight edge board or carpenters square
- A screw gun
With these simple and possibly household tools, you can follow the steps below to install your Focal Point crown molding kit.
1. Measure the Molding
you need along your wall. If you’re using Moulding Mates connectors, measure from the corner to the center of the wall. You’ll want a similar measurement for a piece of our crown molding.
2. Cut the Molding
You have a few options when it comes to choosing a method to cut our Focal Point crown molding.
You May Like: How To Stop Mold Smell
Now Set Up The Table Of The Product That Is Miter Saw To Create Cut At 90 Degrees Angle
By cutting the joint even to 45 degrees, you will still need to cut a piece to fix the walls length. Moreover, you can also skip this step if your crown molding is already cut in sizes.
The person also can use a handsaw or a miter template saw in the place of the miter saw. A template miter saw comes with a plastic box and an open-top that will offer slots for a handsaw.
The Person Should Remove Most Of The Wood From The End While Doing With Coping
Using the coping saw, the worker should start cutting the object. But these methods will not be as perfect if you begin the miter saw for creating cuts in the crown molding inside corners. Likewise, work slowly with the items help and try to adjust the angles of the miter saw before starting the operation.
Those people who create a small vertical cut in crown molding can do all these things easily and with full accuracy and efficiency. These cuts will be found at the back of the moldings. So make sure to perform every single step of this process.
Recommended Reading: What To Use To Get Mold Off Walls
Cut Crown Molding With Just A Miter Box
Do you struggle to understand the fundamentals of cutting the perfect crown molding corners ?
Have you watched instructional video after instructional video trying to learn coping just to wind up either more confused or buying expensive tools that will supposedly make your life easier?
Or maybe you simply only have a basic miter box and need to know IF cutting crown molding is even possible…
This was me on my first time doing crown molding.
I heard from everyone how a cheap and “easy” fix to making your house look more lux is to add some molding. Did you see that word? “Easy.” Ha! Apparently the authors of such articles never cut their own crown molding! Crown molding is anything but “easy.”
However, out of hundreds of crown molding videos and tutorials, I finally found a trick that ACTUALLY WORKS and made it simple for me to understand exactly how to cut the corners without all the confusing ways to turn it and this and that. So I feel obliged to share this exciting AND SUPER EASY trick with you!
So can you cut crown molding with just a miter box? YES! 🙂 And I’m going to show you how!
P.S. I do NOT profess to be a professional or a carpenter of any kind , but I believe in spreading the helpful knowledge I learn to other noobs like me because even if it’s not perfect, it’s better than never trying in the first place. 🙂
Editor’s Note: Turn The Room Into A Workshop
I’ve installed miles of crown molding, so you might think every piece I cut slips perfectly into place on the first try. Wrong. I intentionally cut each piece a smidgen too long and then shave them with my miter saw until they fit perfectly. Sometimes I make three or four trips back to the saw before I finally get it right. To keep the trips short, I set up shop in the room I’m working on. This can take an hour or more and makes a mess, but it saves time in the long run. Here’s some setup advice:
- Get everything you can out of the room. Some pieces of trim might be longer than the room itself. You need space to maneuver.
- Keep the miter saw mobile. You’ll need to move the saw from one end of the room to the other to accommodate long pieces. Setting the saw on sawhorses or a stand is only practical if you can easily move it around. In most cases, I simply set the saw on the floor and support the trim with a small block the same height as the saw’s table.
- You’ll need a sturdy work surface that lets you clamp down the crown molding for coping. It doesn’t have to be big, just stable. I use a Black & Decker Workmate.
- Set up two ladderseven if you’re working alone. Otherwise, you’ll spend half your time dragging a ladder from one end of the wall to the other.
- Cover carpeted floors with dropcloths hardwood floors with cardboard or hardboard. You can work a lot faster when you’re not worried about damaging the floor.
Also Check: How To Fix Black Mold
How Do You Measure And Cut Corners On Crown Molding
When you cut crown molding, measuring the accurate angle is essential for the smoothness and right fitting of the molded sections. Therere multiple ways to measure the crown molding cutting angles. It includes the use of a protractor or crown molding angle calculator. You can even use set-squares and compass for the purpose. Lastly, therere digital scaling devices for the accurate measurement of the angle also.
Last Tips For Cutting Crown Moulding & Painting:
One thing to consider when youre painting crown moulding is the overall quality of the paint. The quality needs to be supreme. Advance by Benjamin Moore is a great high-end durable finish for trims and crown moulding. Sherwin Williams ProMar Classic is another good choice for a high-performance finish thats smooth and durable too.
When youre thinking about ceiling paint colours, the trend is to go a flat white on ceilings. Its best to use the Ultra Spec white we previously mentioned or Benjamin Moores Waterborne Ceiling Paint. This paint is the best to use for rooms with a lot of light exposure as you wont be able to spot any defects. Sherwin Williams ProMar 400 latex interior paint is another good choice.
Also Check: How To Check Your House For Mold In The Air
How To Cut Crown Molding Inside Corners With A Miter Saw
Last Updated on 9 months by James D. Miller
A miter saw has a myriad of functions, and cutting the crown molding inside and outside corners is one of them. Although cutting molding corners are not tricky, you need to accurately set up the crown molding miter angles for precision and better results.
We calculate the cutting angle based on the project requirements. There is also a crown molding angle calculator available to find the desired angle correctly. Hence, today our discussion includes how to cut crown molding inside corners with a miter saw.
Our tutorial also includes tips on cutting the outside corners, cutting angle types, angles chart, etc., to give you a full-on idea on the miter saw usage for crown molding.
Easy Ways To Cut Crown Molding For Corners
You might want a simple method to cut crown molding perfectly, so that it fits over the tricky corners of your ceilings where they meet the walls. By following a few easy tips, you can cut the moldings of the corners without much trouble, and give it a tidy look. Doing it yourself helps cut down on expenses that you could incur in hiring a contractor.
Tools and Materials Needed:
- Safety glasses
Step 1: Choosing the Cut Technique
The most popular and easy ways to cut the corners of moldings are either placing the molding upwards, and setting the saw angle in the desired manner, or cutting it by laying it down flat on the saw table and then fixing it up against the wall corner. Make sure that your miter saw is sharp, and chosen according to the size of the molding. For moldings more than 10 inches wide, you must use a compound saw. For anything less than this, the miter saw must be double the width of the crown molding.
Step 2: Measurements
Step 3: Deciding the Angles
Determine the angles for the corners. Generally a 45 degree angle is suggested. The miter saw has an in built set up for this degree and aids in making smooth cuts. After the first molding is cut, the next piece needs to be cut at a reverse angle.
Step 4: Cutting at the Outside Corners
Step 5: Cutting the Inside Crown Molding Angles
Read Also: How To Clean Mold Off Wood Cabinets
Do You Need A Nailing Strip
It’s a good idea to install a triangular nailing strip in the corner behind the crown molding. It should be secured to the ceiling joists, not the top wall plate.
I always install an angled filler strip along the entire length of each wall that fills up the hollow spot created by the angled crown molding.
You can almost always make a perfect strip cutting a 2×2 piece of lumber at a 45-degree angle with a table saw.
Drive a test nail about one-half inch below the ceiling at random locations to see if you can find this top plate. With this strip in place, you can easily and quickly nail the crown molding in place without using a divining rod or mystic powers to locate wall studs or ceiling joists.
Remember, my Crown Molding eBook has complete step-by-step instructions with tons of color photographs that show you exactly how to cut crown molding. 100% Satisfaction Guarantee!
Column 234
Three: Prime The Pieces
Once all the cuts and joints are well cut, it is time to prime the wood. It is not necessary to prime the MDF molding again if it already has a primer on it. If you are using bare wood, then you can go ahead and prime it. Let it dry completely before installing.
If you prefer, you can go ahead and paint the pieces with finishing paint before fixing the crown molding. It will make your work easy because you do not have to repaint it. Some people choose to paint the pieces after correcting them.
Make sure that the wall studs are easily visible by marking them with a pencil. When you start the installation, you will need to identify these places. Marks should be visible on the ceiling and the wall.
Recommended Reading: How To Get Mold Off Shower Walls
Cutting The Inside Corners Of The Crown
The initial setup required for cutting the outside corners and inside corners is the same. The difference is only in the cutting angles of the saw.
Angles required to cut the inside corners are exactly in the opposite direction than that of the angles required to cut the outside corners.
When cutting is required at a corner with an angle of 90 degrees, we have to cut the piece of crown at a certain angle and then rejoin them together.
If you want to perform crown molding cutting, you must have a high quality saw with a bevel which helps in tilting the saw.
However, if you have a compound miter saw, then cutting crown molding is not a difficult task.
You must have a measuring tape to measure the sizes of the crown molding for cutting.
